データ復旧・データ消去技能者の個人ブログ

HAYATO.NET

未分類

ハードディスクの静音化ツール HGST IBM FeatureTool

更新日:

ちょっと MASAMUNE の話題をFaceBook でしてたら、面白いものを見て思い出してビールを吹いてしまった。

そういえば、ハードディスクを静音化するツールがあったなぁと。

ツールの名前は IBM Feature Tool。

今ではちょっとデータ復旧かじってるエンジニアだったら Drive Fitness Test の方が有名だったりしてないかな??(SeaToolsは まだ生きていたようなぁ。。)

HGSTのページ探したけど見つからず。

(あった!http://www.hgst.com/support/index-files/simpletech-legacy-downloads

Feature Tool 2.15のダウンロード

一応 ダウンロードページは生きていた。

ISOをDAEMON TOOL にマウントしていじいじ。

10年前 このツールにデータ復旧の秘密があるかも?と思っていじってた時代があったなぁ。

今日はふりだしに戻って考え直してみる。

参考サイト:

FeatureTool(Hitachi,旧IBM)でのHDD静音化方法

Hitachi Feature ToolでHDDのガリガリ音を消して静音化する方法! - 裏技shop DD

追記 03:19

懐かしい型番がいっぱい!

IBM-DJAA-312 IBM-DJAA-317 IBM-DJAA IBM-DMCA-21080 IBM-DMCA-21440 IBM-DMCA IBM-DTNA-218 IBM-DTNA-221 IBM-DTNA IBM-DCRA-221 IBM-DCRA-214 IBM-DCRA IBM-DDLA-2108 IBM-DDLA-21215 IBM-DDLA-21620 IBM-DDLA IBM-DLGA-22690 IBM-DLGA-23080 IBM-DLGA IBM-DAQA-3216 IBM-DAQA-3270 IBM-DAQA-3324 IBM-DAQA IBM-DCAA-32880 IBM-DCAA-33610 IBM-DCAA-34330 IBM-DCAA IBM-DTCA-23240 IBM-DTCA-24090 IBM-DTCA IBM-DPLA-24480 IBM-DPLA-25120 IBM-DPLA IBM-DHEA-34330 IBM-DHEA-34860 IBM-DHEA-36480 IBM-DHEA-34331 IBM-DHEA-36481 IBM-DHEA-38451 IBM-DHEA IBM-DYKA-221 IBM-DYKA-232 IBM-DYKA IBM-DYLA-26480 IBM-DYLA-27900 IBM-DYLA-28100 IBM-DYLA IBM-DKLA-212 IBM-DKLA-221 IBM-DKLA-232 IBM-DKLA-243 IBM-DKLA IBM-DADA-248 IBM-DADA-25 IBM-DADA-26 IBM-DADA IBM-DTTA-3503 IBM-DTTA-3504 IBM-DTTA-3506 IBM-DTTA-3508 IBM-DTTA-3510 IBM-DTTA-3512 IBM-DTTA-3513 IBM-DTTA-3516 IBM-DTTA-35 IBM-DTTA-3710 IBM-DTTA-3712 IBM-DTTA-3714 IBM-DTTA-37 IBM-DBCA-206 IBM-DBCA-204 IBM-DBCA-203 IBM-DBCA IBM-DCXA-210 IBM-DCXA-208 IBM-DCXA IBM-DCYA-214 IBM-DCYA IBM-DJNA-3510 IBM-DJNA-3515 IBM-DJNA-3520 IBM-DJNA-3525 IBM-DJNA-35 IBM-DJNA-3706 IBM-DJNA-3709 IBM-DJNA-3710 IBM-DJNA-3713 IBM-DJNA-3718 IBM-DJNA-3722 IBM-DJNA-37 IBM-DMDM-100170 IBM-DMDM-100340 IBM-DMDM IBM-DPTA-3511 IBM-DPTA-3515 IBM-DPTA-3522 IBM-DPTA-3530 IBM-DPTA-3537 IBM-DPTA-35 IBM-DPTA-3710 IBM-DPTA-3713 IBM-DPTA-3720 IBM-DPTA-3727 IBM-DPTA-3734 IBM-DPTA-37 IBM-DARA-2060 IBM-DARA-2090 IBM-DARA-2120 IBM-DARA-2150 IBM-DARA-2180 IBM-DARA-2225 IBM-DARA-2250 IBM-DTLA-30501 IBM-DTLA-30502 IBM-DTLA-30503 IBM-DTLA-30504 IBM-DTLA-305 IBM-DTLA-30701 IBM-DTLA-30702 IBM-DTLA-30703 IBM-DTLA-30704 IBM-DTLA-30706 IBM-DTLA-30707 IBM-DTLA-307 IBM-DJSA IBM-DSCM-10540 IBM-DSCM-11000


Ftools.exeから

Displays this message

  Drive options:

   /Dx          Select the drive (0 = Master, 1 = Slave).

   /Cxx         Select the IDE controller

                 0 = Primary, 1 = Secondary controller.

                20 = PCI IDE primary, 21 = PCI IDE secondary controller.

                22 = Second PCI IDE primary controller ...

   /ALL         Selects all installed IDE drives.

  Command:

   /AAM         Modify automatic acustic management level.

   /APM         Modify advanced power mode.

   /Clip        Change (Clip) drive capacity.

   /Info        Displays some drive information.

   /RC          Read-Ahead cache switch.

   /UDMA        Ultra DMA mode switch.

   /WC          Write cache switch.

   /SS          Modify SATA xfer speed and SSC setting.

 Syntax to modify the automatic acoustic management (AAM) level:

   /AAM  [STATUS | | ENABLE | DISABLE] <VALUE>

   Options:

     STATUS          Display the current AAM status.

     ENABLE          Enable AAM.

     ENABLE <value>  Enable AAM with the given value.

     DISABLE         Disable AAM.

   Example:

   - This command displays the current AAM status for all drives:

     FTOOL.EXE  /ALL  /AAM  STATUS

   - This command disables the AAM on the primary IDE master drive:

     FTOOL.EXE  /C0  /D0  /AAM  DISABLE

 Syntax to modify the advanced power mode level (APM) level:

   /APM  [STATUS | | ENABLE | DISABLE] <VALUE>

   Options:

     STATUS          Display the current APM status.

     ENABLE <value>  Enable APM with the given value.

     DISABLE         Disable APM (Not supported on all products).

     DEFAULT         Set the default APM value.

   Example:

   - This command displays the current APM status for all drives:

     FTOOL.EXE  /ALL  /APM  STATUS

   - This command disables the APM on the primary IDE master drive:

     FTOOL.EXE  /C0  /D0  /APM  DISABLE

 Syntax to change (clip) the drive capacity:

   /CLIP  [SAVE | NO_SAVE]  [LBA | CYLINDER | MB | GB]  VALUE

   Options:

     SAVE              Save permanent.

     NO_SAVE           Save temporary. Clipping is reset after next Power On                       (good for experimenting)

     LBA      <value>  Max Logical Block Addresses (LBA)

     CYLINDER <value>  Number of logical drive cylinders.

     MB       <value>  Number of Megabytes (1 MB = 1'000'000 bytes).

     GB       <value>  Number of Gigabytes.

     A <value> of 0 changes the drive capacity to the maximum !

   Example:

   - This command clips the secondary slave drive to 15 GB (permanently):

     FTOOL.EXE  /C1  /D1  /CLIP  SAVE  MB  15000

 Syntax for ultra DMA mode switch:

   /UDMA [MODE | DISABLE]

   Options:

     MODE       Change the maximum ultra DMA mode to the given value (0 - 5).

     DISABLE    Disables the ultra DMA support.

     In order for the change to take effect, you MUST power off your system.

     Pressing the CTRL-ALT-DEL key is not enough !

   Example:

   - This command change the maximum ultra DMA speed to ATA 33 (UDMA 2).

     FTOOL.EXE  /UDMA  2

   - This command disables the ultra DMA support.

     FTOOL.EXE  /UDMA  DISABLE

 Syntax for Write Cache (WC) switch:

   /WC  [STATUS | ENABLE | DISABLE]

   Options:

     STATUS          Display the current write cache status.

     ENABLE          Enable write cache.

     DISABLE         Disable write cache.

   Example:

   - This command displays the current write cache status for all drives:

     FTOOL.EXE  /ALL  /WC  STATUS

   - This command enables the write cache on the primary IDE master drive:

     FTOOL.EXE  /C0  /D0  /WC  ENABLE

 Syntax for Read-Ahead Cache switch:

   /RC  [STATUS | ENABLE | DISABLE]

   Options:

     STATUS          Display the current Read-Ahead cache status.

     ENABLE          Enable Read-Ahead cache.

     DISABLE         Disable Read-Ahead cache.

   Example:

   - This command displays the current Read-Ahead cache status for all drives:

     FTOOL.EXE  /ALL  /RC  STATUS

   - This command enables the Read-Ahead cache on the primary IDE master drive:

     FTOOL.EXE  /C0  /D0  /RC  ENABLE

 Syntax for SATA Setting change:

   /SS  [ HIGH | LOW ] [ ENABLE | DISABLE ]

   Options:

     HIGH          Set SATA transfer speed to 3.0Gbps.

     LOW           Set SATA transfer speed to 1.5Gbps.

     ENABLE        Set SSC Enable.

     DISABLE       Set SSC Disable.

   Example:

   - This command set the SATA transfer speed to 3.0Gbps and enable SSC on the primary IDE master drive:

     FTOOL.EXE  /C0  /D0  /SS HIGH ENABLE

 No help information available !

-未分類
-, , ,

Copyright© HAYATO.NET , 2024 AllRights Reserved Powered by STINGER.